I would first suspect the wiring coming out of the Hazard Switch to the Left turn signal, the Dark Green/Red wire on pin 7 of the Hazard Switch/Combination Flasher. Put a meter on this pin 7 and check if you get +12 volts there when the Hazard switch is pressed or when the Left Turn Stalk is activatedif +12 volts is there then there is a In this video my boys help me replace the turn signal switch on my 2003 Jeep Grand Cherokee WJ. It was a great time working with them. I love it when I get a

if the hazards work on all 4 corners, then everything from the switch out, is good, and if the right turn signal works, then it has all the power sources and grounds, this only leaves the combination flasher as the culprit, it has seperate sense wires for left turn, right turn, and hazzards, so if the switch has already been replaced, then it has to be in the combination flasher,Tim

I have owned the Jeep since 2016. 2007 Jeep Grand Cherokee WK Limited, 5.7 L; I am the second owner, full service records; Currently has 129k on the odometer; The issue occurred while on a roadtrip. I wound up driving about 200 miles with the signal the way it was (hand signals for right, holding the signal in left or right when not turning left). My 1999 Grand Cherokee has a problem with left directional. Sometimes it just stops working. The next day it works fine again. I changed the left turn light bulbs, and the multi function switch. Same problem. This has been going on for two months. Optional Information: 1999 Jeep Grand Cherokee 4.0 Already Tried: light bulbs and multi function Remove the entire console. Slide the shifter beezel as far up vertically as you can. There are 4 clips you ned to remove to do it. You will see a blue and black wire running into the back. Follow those wires to the resistor. You will see a transparent EL panel attatched to the resistor by two clips. V8. 4WD. AUTOMATIC. 120,000 MILES. While driving the left turning signal stays on. Tried removing one of the relays but was told there is not one. Put relay back in but now other relays are clicking and back tail light is draining battery. I am thinking relay is bad after I removed from PCM. I do not have a diagram of the combination module

Driver side rear lights - when I turn on the lights, all tail lights are okay but when I press the brake pedal all lights go out on the rear driver side. Without lights on the brake light on the left side doesn't work. Turn signal, tail light, and backup lights work until you step on the brake. Every thing works on the passenger side.

ASE Certified Technician. High School or GED. 26,564 satisfied customers. 2000 Jeep Cherokee: are intermittent..hazard lights always work. Turn signals on a 2000 Jeep Cherokee are intermittent. They work normall or not at all. The hazard lights always work, even when the turn signals … read more. 1. check your turn signal light bulbs to see if one is burned out or partly burned out. One filament may be broken. Do it with lights on and off. Check brake lights. If one not working that is the problem bulb. Check front and back lights. 2. replace your turn signal flashers in fuse panel
Having similar issues I replaced the back up light and the turn signal bulb but they still dont work. Head lights work rear pass turn signal light works, and break lights work. I think its eletrical I found some connections under the bench seat behind the driver seat that there were two wires not connected to anything. and the left turn signal
1 post · Joined 2012. #1 · Jan 30, 2012. So I started with no tail lights and 1 missing brake light. All other lights (interior, front, turn signals) worked fine. I changed bulbs - still no luck. Changed fuses - no luck. Read a prior post about the adjusting the chrome pieces on the metal assembly.. tried it and now the brake lights both work
Hey how are you. This is Your response, sorry this is not texting sorry takes longer ,so you have to be patient for you answer . Thank You. 1- check all fuses first in the inside of the cabin fuse box , but since it is intermittent , that means fuse is good and like the tech said at jiffy lube , the combination switch is a common issue with intermittent condition on the turn signal switch
If power is not getting to the turn signal pin, then a fuse may be blown or it is missing. If either of these is the case, then replace the missing or broken fuse. If power is getting to the trailer turn signal pin, then the issue could be a loose ground wire. Don’t replace the whole light if this is the problem. KKQxUlv.
  • 70p55lvt8b.pages.dev/381
  • 70p55lvt8b.pages.dev/133
  • 70p55lvt8b.pages.dev/438
  • 70p55lvt8b.pages.dev/404
  • 70p55lvt8b.pages.dev/298
  • 70p55lvt8b.pages.dev/348
  • 70p55lvt8b.pages.dev/455
  • 70p55lvt8b.pages.dev/270

    • jeep grand cherokee left turn signal not working